loading

Focus on laundry equipment since 1991's

There are winding problems and some faults in the washing equipment

by:GOWORLD     2020-02-25

washing equipment how to deal with the twining of washing linen? How to solve the problem of cloth Twining in washing equipment?

under normal circumstances, as long as the washing equipment is operated correctly, there will be no winding phenomenon. When using the washing equipment, we should operate according to the washing process specification, first of all, it is necessary to sort the linen. This is a very important step. The phenomenon of clothes Twining when washing the washing equipment is because we did not follow the process, if the winding phenomenon occurs, it will not only seriously affect the service performance and efficiency of the washing equipment, but also seriously restrict the service life over time, and also restrict the cleanliness of the washed fabric, so how do we avoid the winding problem of laundry equipment? How to solve the winding problem? First, we should pay attention to avoid winding phenomenon, washing equipment washing fabric winding phenomenon, basically because the operator failed to operate according to relevant specifications when putting fabric into its inner cylinder, without sorting, a pile of fabric was directly put in, and at the same time, it was not able to stir up in time when washing, so there was entanglement. To some extent, the quality of the washing equipment itself is not good, and objectively speaking, it is improper operation. Therefore, in order to prevent the fabric from winding, when we put the fabric into the washing equipment drum, we should put it separately according to the relevant specifications. Second, how should we solve the winding phenomenon of washing equipment and cloth? When this situation occurs, many operators basically manually separate the wound fabrics, since the fabrics processed by the washing equipment itself belong to the large category, it is very difficult to operate. The author thinks that in this case, you can buy laundry balls in supermarkets or shops and put them in the inner barrel of washing equipment, which can effectively avoid problems such as winding and knotting in the laundry process; In addition, when taking clothes, press the key of taking clothes to make the forward rotation and reverse rotation of the roller alternate, shaking and dispersing the clothes to facilitate taking out. Fault 1: Stop water intake when the water intake does not reach the set water level. Analysis and maintenance: This fault is mainly due to the poor performance of the water pressure switch. When the air pressure in the gas collection chamber has not yet reached the specified pressure, the contact will be switched from the open state to the closed state in advance and the water will stop. The specific reasons and treatment methods are as follows: 1. The pre-compression quantity of the water level control spring of the water pressure switch becomes smaller, and the pre-compression quantity of the water level control spring can be solved as long as the screw-in adjustment screw is increased. If the elasticity of the water level control spring becomes smaller or loses elasticity, the water level control spring should be replaced. 2, water pressure switch Cam groove wear or damage, generally to replace the cam can be solved. Fault 2: The water intake must exceed the set water level before stopping the water intake. Analysis and maintenance: This phenomenon shows that when the actual water level has reached the specified height, the air pressure in the gas collection chamber of the water pressure switch still cannot reach the specified value, and the water pressure switch will only act if the water level continues to rise. The specific reasons and treatment methods are: 1. The Air guide nozzle of the gas collection chamber of the water pressure switch is blocked or leaked. As long as the debris at the Air guide nozzle is removed; Or seal with 401 glue at the air leakage. If the air guide hose is aging, kink or broken and leaking, replace the Air guide hose. 2, water pressure switch water level control spring preloading shrinkage is too large. As long as the adjustment screw out of some, reduce the water level control spring pre compression. 3. The reversing ejector rod and transmission parts in the water pressure switch are deformed or damaged. It can be solved by repair and correction, and the water pressure switch should be replaced when it is serious. Fault 3: When the program enters the Washing State, the motor rotates normally, but the wave wheel does not rotate. Analysis and maintenance: this fault mostly occurs in the mechanical transmission part between the washing machine motor and the wave wheel. The specific reasons and treatment methods of washing equipment are: 1. The fastening screws of motor pulley, clutch pulley and wave wheel are loose, sliding wire or broken. Just re-tighten or replace the fastening screws; If the square hole of the wave wheel is rounded, the wave wheel should be replaced. 2, triangle belt slip or fall off. As long as the distance between the motor and the clutch is properly adjusted and the friction is increased by rubbing some rosin powder on the triangle belt. If the triangle belt is aging and deformed, the triangle belt should be replaced. 3, clutch deceleration mechanism parts wear or damage, generally need to replace the clutch assembly. Fault 4: When washing, the dewatering bucket will follow. Analysis and maintenance: the dewatering bucket is divided into two situations. One is that the dewatering bucket rotates clockwise; The second is that the dewatering bucket rotates counterclockwise. The specific reasons and treatment methods for the clockwise rotation of the dewatering bucket of the washing equipment are as follows: 1. The brake belt is loose, so that the braking torque of the brake belt to the dewatering shaft is reduced, as long as the brake belt is reinstalled. 2, brake belt is seriously worn or damaged. By rotating the adjusting screw, the pawl position can be properly adjusted to increase the braking torque of the brake belt on the dewatering shaft, and the brake belt should be replaced when it is serious. The specific reasons and treatment methods for the counterclockwise rotation of the dewatering bucket of the washing equipment are as follows: 1. The clutch torsion spring falls off and breaks or the torsion spring and the dehydration shaft are too loose and slip, so that the torsion spring loses the reverse function. Just reinstall the torsion spring or replace the torsion spring, and replace the reducer when it is serious. 2, clutch brake belt loose, wear or fracture. Just tighten or replace the brake band. 3, washing equipment clutch brake spring or shift fork spring is too soft or broken. Just replace the clutch brake spring or shift fork spring to solve the problem.
There are many issues that affect laundry machine producer, which has led to the need of getting specialists trained in certain areas so as to handle all issues that may arise as well as laundry equipment suppliers products that can solve laundry products producer problems.
With all the pros and cons of different in mind, click GOWORLD LAUNDRY EQUIPMENT to learn more about and decide which laundry equipment suppliers option is best for your case.
FOSHAN GOWORLD LAUNDRY EQUIPMENT CO., LTD employs a numbers of citizens, helping them and their families achieve a higher standard of living.
Custom message
Chat Online
Chat Online
Leave Your Message inputting...
Sign in with: